• Cup Boat Stand

    Each stand kit is made from select woods, cut to size and drilled as required. Nylon support straps and all hardware is included. The Cup stand is sized for the V-32, Australia II and the Stars & Stripes. Estimated shipping charges quoted are for the continental U.S. only.
    $32.95
  • Hitec 311 Servo

    Control System: +Pulse Width Control 1500usec Neutral Required Pulse: 3-5 Volt Peak to Peak Square Wave Operating Voltage: 4.8-6.0 Volts Operating Temperature Range: -20 to +60 Degree C Operating Speed (4.8V): 0.19sec/60° at no load Operating Speed (6.0V): 0.15sec/60° at no load Stall Torque (4.8V): 42 oz/in (3.0 kg/cm) Stall Torque (6.0V): 51 oz/in (3.7 kg/cm) Current Drain (4.8V): 7.4mA/idle, 160mA no load operating Current Drain (6.0V): 7.7mA/idle, 180mA no load operating Dead Band Width: 5usec Operating Angle: 45° one side pulse traveling 450usec Direction: Multi-directional Motor Type: Cored Metal Brush Potentiometer Drive: 4 Slider/Direct Drive Bearing Type: Top Resin Bushing Gear Type: Nylon Continuous Rotation Modifiable: Yes Connector Wire Length: 11.81" (300mm) Weight: 1.52oz (43g) used in rudder application in all boats, sail application in 24" and under boats. Estimated shipping charges quoted are for the continental U.S. only.
    $18.95
  • HITEC 755 Sail Winch

    This lightweight, fast acting, sail winch is perfect for skippers who need that competitive edge. The servo is equipped with Karbonite gears for super wear resistance and includes a 2 sided arm for simple rigging. The servo rotates 90 degrees with a torque of 183 in oz. @ 6 vdc. It's size is 2.3 x 1.1 x 2.0.Estimated shipping charges quoted are for the continental U.S. only.
    $65.95
  • HITEC 815 Mega Sail Servo

    This fully proportional large-scale aircraft servo has been specially set up to rotate approximately 180 degrees. The servo used as a winch will handle Valkyrie size models. The size is 2.5 x 1.25 x 2.25 in. with a torque of 237 in. oz. and weighs 4.75 oz. Estimated shipping charges quoted are for the continental U.S. only.
    $79.95
  • Large Boat Stand

    Each stand kit is made from select woods, cut to size and drilled as required. Nylon support straps and all hardware is included. The Large stand will support models with a keel depth up to 14 inches.Estimated shipping charges quoted are for the continental U.S. only. Estimated shipping charges quoted are for the continental U.S. only.
    $42.95
  • Lazarette Kit

    (Rudder access hatch for Soling IM) Includes molded ring and hatch cover. Easy installation, Cut a 2 1/2 x 2 3/4 inch hole in the deck, insert the ring from the underside and glue in place. Estimated shipping charges quoted are for the continental U.S. only.
    $16.95
  • Mary J. Ward Stand

    Wooden boat stand for static display,with brass plaque. Estimated shipping charges quoted are for the continental U.S. only.
    $52.95
  • Mini Boat Stand

    Each stand kit is made from select woods, cut to size and drilled as required. Nylon support straps and all hardware is included. The Small stand fits the Snipe and Mini Soling. Estimated shipping charges quoted are for the continental U.S. only.
    $19.95
  • Option I

    The radio package includes the exceed 6 ch and receiver the 311 rudder servo and the 311 sail winch This unit is ideal for control of models up to 24 inches in length since this size model does not require a larger sail winch.Estimated shipping charges quoted are for the continental U.s. only.
    $99.95
  • Option II

    This package includes the features of the Option I radio package except one of the 311 servos is replaced by the powerful HS 755 Quarter Scale servo for a sail winch. This unit is fitted with Karbonite gears for super long lasting service. The servo is rated at 183 in oz torque at 6VDC and is ideal for models up to the Avalon in size. Estimated shipping charges quoted are for the continental U.S. only.
    $179.95
  • Reinforced Sail Corners

    Reinforced Corners for Dacron Sails, sold only with sails cannot be purchased seperately
    $12.00
  • Soling 1 Meter Keel Pouring Stand

    Keel Stand and 2 funnels for pouring the lead and resin in the Soling 1 meter keel. works for the V-32 Keel as well. Estimated shipping charges quoted are for the continental U.S. only.
    $13.95
  • V-12A Footy stand

    This display stand is sized for the Footy class models. All parts are cut and drilled for easy assembly.
    $19.95
  • Wall Mount Boat Stand

    Unfinished wall mounted boat stand
    $39.95